Being able to show off your yard after a great landscaping job is done is a huge source of pride. Many neighborhood associations give rewards to those that take the extra time and effort to make their yard look great. One aspect of this is having a clear delineation between the flowerbeds and the grassy turf. Using a plastic bender board is a great way to accomplish this. The material keeps weeds at bay and will prevent the turf from growing into the flowerbeds or other decorations you want to protect.
Two types are in use. One is made from natural wood fibers. These work great, but over time will deteriorate and be absorbed into the soil. They will have to be replaced in time. The plastic version is made from recycled materials and won't fall apart or deteriorate over time. It will last for years and do the job effectively.
The first step in placing them is to figure out how long they should be. One method is to place stakes at intervals along the path where they will be placed. Stretch a string between each stake and when finished, measure the length of the string. This prevents you from having to measure every angle and twist in the path and still be sure you have enough material. If you're unsure, add some inches to the final measurement.
Next, you want to dig the trench. Make sure it is at least six inches in width and deep enough to allow the board to sit below the surface. You will want to cover the board with dirt when you are done, so keep the dirt close by for the last step. For this process, you can place a piece of tape or paint on the shovel or keep a ruler handy to measure both the width and depth.
Put in the stakes. This process is important because it will hold the border in place. Put stakes every few feet or according to the manufacturer's suggestions. Where there is a break in the material, put in an extra stake to help hold the two ends together and prevent a gap.
The fourth step is to cut the material to length and place in the ground. It is easier if you roll the material out next to the trench. When done, make your cuts and slide the border into the hole and secure it to the stakes. This keeps it in place. If you notice any areas that are riding too high and will be exposed, just use a trowel and dig the dirt out from under it and place it to the side.
You are finally ready to fill in the hole. The dirt you set aside earlier should be right next to the trench. Just use a shovel or rake to fill it in and cover the board. You should use all the dirt and have a bit of a mound on top. This will settle over time. If you want to begin placing a rock border, feel free to start the process after you tamp down the dirt to make it nice and compact. If you wait for the next project the dirt will settle and you won't have to go back and work the rock formation again.
Once all of this is done your border will look great. Allow some time for the mound over the path to settle. If you are going to place rocks over it to beautify it, feel free to do that right away as this will help it settle faster. This will keep the weeds and turn from growing into the flower beds.
Two types are in use. One is made from natural wood fibers. These work great, but over time will deteriorate and be absorbed into the soil. They will have to be replaced in time. The plastic version is made from recycled materials and won't fall apart or deteriorate over time. It will last for years and do the job effectively.
The first step in placing them is to figure out how long they should be. One method is to place stakes at intervals along the path where they will be placed. Stretch a string between each stake and when finished, measure the length of the string. This prevents you from having to measure every angle and twist in the path and still be sure you have enough material. If you're unsure, add some inches to the final measurement.
Next, you want to dig the trench. Make sure it is at least six inches in width and deep enough to allow the board to sit below the surface. You will want to cover the board with dirt when you are done, so keep the dirt close by for the last step. For this process, you can place a piece of tape or paint on the shovel or keep a ruler handy to measure both the width and depth.
Put in the stakes. This process is important because it will hold the border in place. Put stakes every few feet or according to the manufacturer's suggestions. Where there is a break in the material, put in an extra stake to help hold the two ends together and prevent a gap.
The fourth step is to cut the material to length and place in the ground. It is easier if you roll the material out next to the trench. When done, make your cuts and slide the border into the hole and secure it to the stakes. This keeps it in place. If you notice any areas that are riding too high and will be exposed, just use a trowel and dig the dirt out from under it and place it to the side.
You are finally ready to fill in the hole. The dirt you set aside earlier should be right next to the trench. Just use a shovel or rake to fill it in and cover the board. You should use all the dirt and have a bit of a mound on top. This will settle over time. If you want to begin placing a rock border, feel free to start the process after you tamp down the dirt to make it nice and compact. If you wait for the next project the dirt will settle and you won't have to go back and work the rock formation again.
Once all of this is done your border will look great. Allow some time for the mound over the path to settle. If you are going to place rocks over it to beautify it, feel free to do that right away as this will help it settle faster. This will keep the weeds and turn from growing into the flower beds.
About the Author:
When you are looking for information about plastic bender board, come to our web pages online today. More details are available at http://www.bestedging.com now.
No comments:
Post a Comment